BS EN 10002-1 PDF

The Green document status indicator indicates that the document is: a current in the Construction Information Service and b the latest version - ie it does not have any other documents that replace or amend it and is promoted as a current document by the publisher. The Amber document status indicator indicates that some caution is needed when using this document - it is either: a current in the Construction Information Service but has a document or documents that replace or amend it, so please look at the "Newer Versions" tab or b not in the Construction Information Service but with another reason why it may be relevant to our customers such as being cited in NBS or in the Building Regulations Approved Documents. Again there may be more recent versions of the document. The Red document status indicator indicates that the document is an old version The document has likely been withdrawn by the publisher, also the meta data presented here may be out of date as it is no longer being maintained by the editorial teams at NBS.

Author:Yoramar Meztishicage
Country:Denmark
Language:English (Spanish)
Genre:Life
Published (Last):2 September 2006
Pages:211
PDF File Size:10.87 Mb
ePub File Size:11.74 Mb
ISBN:462-6-84234-730-6
Downloads:82577
Price:Free* [*Free Regsitration Required]
Uploader:Shaktit



Faebar EN was composed of five parts: The minimum transition radius between the grips ends and the parallel length shall be: It should be noted that when evaluating the total scatter in experimental results the uncertainty in measurement should be considered in addition to the inherent scatter due to material inhomogeneity.

A type B evaluation is based on some other means ; Thus the use of tolerances specified in a standard comes under the type B category. If the material tested has no yield phenomena, the proof strength Rp0,2 should be used. There are two types of non-proportional test pieces, with dimensions as given in Table B.

Method of test at ambient temperature Status: NOTE This clause only applies to materials having yield phenomena and when Ae is not required to determined. By continuing to use our site, you accept our cookie policy. Typical example of data sets used to determine materials response over the strain rate range specified in EN is shown in Figures J. For very thin materials, it is recommended that strips of identical widths should be cut and into a bundle with intermediate layers of a paper which is resistant to the cutting oil.

Within the plastic range and up to the proof strength non-proportional extension or total extension the strain rate shall not exceed 0, 5 s The cross-section of the test pieces may be circular, square, rectangular, annular or, in special cases, of some bx shape.

They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. Method of test at ambient temperature. Amendments issued since publication Amd. The gripped ends may be of any shape to suit the grips of the testing machine.

Customers who bought this product also bought BS EN It should be noted that the expanded uncertainties have been calculated using a simplified approach based on the GUM. These recommendations are related to the design, the software of the machine and its validation ej to vs operating conditions of the tensile test.

For products of circular cross-section, the original cross-sectional area may be calculated from the arithmetic mean of two measurements carried out in two perpendicular directions. A line is then drawn parallel to this line, at a distance from the corrected origin of the curve, measured along the abscissa, equal to the prescribed non- proportional percentage. In cases of dispute, the value, D, shall be used, as long as there is sufficient material.

After fracture, the broken test piece should be placed in a fixture and axial compressive force applied, preferably by means of a screw, sufficient to firmly hold the pieces together during measurement. Take the smart route to manage medical device compliance. NOTE 2 For some metallic materials highly cold deformed material like for instance double reduced tin plate or irradiated structural steelthe maximum force is not always occurring at the beginning of necking.

Products that may be tested in accordance with this standard include metallic sheets and plates, wire, bar or section, and tubes. Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more! A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.

For the purpose of this analysis, the total of the variation in proof strength over the strain rate range permitted in the standard has been halved and expressed as an equivalent tolerance, i. EN Tensile Testing Metallic Materials — Instron NOTE Wn of percentage elongation are possible only when the gauge length or extensometer gauge length, the shape and area of the cross-section are the same or when the coefficient of proportionality k is the same.

Date Comments Li ce ns ed C op y: In particular it provides the recommendations which should be taken into account in the software and testing conditions.

When an extensometer is used it shall be at least of class 1 according to EN for the determination proof strength non-proportional extension ; for other properties with higher extension a class 2 extensometer according to EN can be used. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.

EN ISOetc. The parallel length Lc shall be connected to the ends by means of een curves with a radius of at least 20 mm. A statistical approach to the analysis of intercomparison exercises Round Robin experiments does not separate out the two contributing causes of the scatter but nevertheless gives a useful indication of the likely range of tensile results measured by different laboratories using similar material.

The latter is obtained by dividing this force by the original cross-sectional area of the test piece So see Figure 3. In particular, a distinction is bss between: An example of the application of these tolerances is given below: Special precautions shall be taken to ensure proper contact between the broken parts of the test piece when measuring the final gauge length.

Details and advice can be obtained from the Copyright Manager. It is incorporated by Royal Charter. TOP Related Posts.

HETEROSPORY AND SEED HABIT IN PTERIDOPHYTES PDF

BS EN 10002-1

.

GAI EATON ISLAM AND THE DESTINY OF MAN PDF

BS EN 10002-1:2001

.

ADEPTUS TITANICUS PDF

DIN EN 10002-1:2001-12

.

BAD BLOOD MARI MANCUSI PDF

.

Related Articles